From Linux NFS

Soft iWARP is a software implementation of RFC 5040, RFC 5041, and RFC 5042 that allows RDMA to be used on any Ethernet adapter using TCP. It is available in Linux kernels after 5.4. The following instructions are suitable for most of the latest Linux distributions.

Contents 1 Client and Server Common Setup 1.1 Ping Test 2 NFS Setup 2.1 Server 2.2 Client 3 See Also

Client and Server Common Setup

• Check for the siw kernel module. If you don't have it, then enable the following Kconfig options and rebuild your kernel

CONFIG_INFINIBAND=y
CONFIG_RDMA_SIW=m

• Install the iproute2 package and use the rdma link add command to load the module and start an RDMA interface. If "eth0" is your local Ethernet interface:

[foo@linux-bar ~]$ sudo rdma link add siw0 type siw netdev eth0
[foo@linux-bar ~]$ sudo rdma link
link siw0/1 state ACTIVE physical_state LINK_UP netdev eth0

The siw virtual device does not survive reboots. Add it to system startup scripts so that it is instantiated automatically after every system restart.

Ping Test

• Start an rping server on one machine

[foo@linux-bar ~]$ sudo rping -s -v -C 3
server ping data: rdma-ping-0: ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqr
server ping data: rdma-ping-1: BCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrs
server ping data: rdma-ping-2: CDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrst
server DISCONNECT EVENT...
wait for RDMA_READ_ADV state 10

• Now check that the connection works from another machine

[foo@linux-bor ~]$ sudo rping -c -a 192.168.122.40 -v -C 3
ping data: rdma-ping-0: ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqr
ping data: rdma-ping-1: BCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrs
ping data: rdma-ping-2: CDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrst
client DISCONNECT EVENT...

NFS Setup

Server

• Install the nfs-utils package and enable rdma from /etc/nfs.conf and restart service nfs-server

[foo@linux-bar]$ sudo sed -i '/rdma/{s/^#//; s/rdma=n/rdma=y/}' /etc/nfs.conf
[foo@linux-bar]$ grep -v ^# /etc/nfs.conf
[general]
[exportfs]
[gssd]
 use-gss-proxy=1
[lockd]
[mountd]
[nfsdcld]
[nfsdcltrack]
[nfsd]
 rdma=y
 rdma-port=20049
[statd]
[sm-notify]
[foo@linux-bar]$ sudo mkdir -p /expdir
[foo@linux-bar]$ sudo bash -c 'echo "/expdir *(rw,no_root_squash)" >/etc/exports'
[foo@linux-bar]$ sudo systemctl restart nfs-server

Client

• Install the nfs-utils package and do nfs mount
• Mount the server to check that it worked

[foo@linux-bor]$ sudo mount -o rdma 192.168.122.40:/expdir /mnt/nfsmp
[foo@linux-bor]$ mount | grep proto=rdma
192.168.122.40:/expdir on /mnt/nfsmp type nfs4 (rw,relatime,vers=4.2,rsize=262144,wsize=262144,namlen=255,hard,proto=rdma,port=20049,timeo=600,retrans=2,sec=sys,clientaddr=192.168.122.161,local_lock=none,addr=192.168.122.40)

See Also

• Rdma-core's documentation
• The rdma man page